Saturday, August 25, 2012

Mini Spy Sound Recorder



Circuit showing a digital spy voice recorder . Ic cxa1619bs is used for making this circuit.The voice or sound recorder built with ISD1012, ISD1016 and ISD1020 which are produced by ISD and allow sound voice recording and play-back. The last 2 digits show the maximum legth of recording time in seconds.The  non-volatile memory in this circuit can memorise sound or voice without power supply up to 10 years. The circuit's input section contains a microphone amplifier and a speaker amplifier.
S1 switch is for recording / play-back ( recording in ON position ). When S2 is OFF the IC goes in power down mode. S3 starts the recording or play-back and must be a push-button.
The circuit is very small so that it can be fabricated on to a very small PCB, and can be used for spy work. 






Tags:spy voice recorder, voice recorder, voice recording circuit, spy voice recording circuit, digital spy circuit, digital spy recorder, spy sound recorder, sound recording circuit

Friday, August 24, 2012

MG University B.Tech results 2012 published






MG University's  B.tech Degree  Semester 8 Exams conducted in May 2012 results will be published very soon.
For viewing the results CLICK HERE

LED Flasher For Automobiles

You can make this circuit and it can be attached to the automobiles for a cool look. For four wheelers it can fixed inside the head lamps and also under body also in two wheelers it can be attached under the vicer or under body etc.

Mini LED Torch



Here is simple circuit for making a LED torch, arrange the LED's in a dot board and attach it at the end of a PVC pipe so that it looks like a real torch

Monday, August 20, 2012

Obstacle detector wrist watch for blind

This is a circuit that helps the blind people to detect the obstacles around them. Here an IR sensor module is used to sense the obstacle in a range of 15-150cm. When an obstacle comes in front of the IR sensor then it detects it by the reflected waves and thereby produces an out put voltage. This output voltage is given to a vibrating motor through an H-bridge IC. That is The vibrating motor starts vibrating when obstacle come front of the watch.







Tags: obstacle detector, IR sensor circuits, inventory circuits, circuit ideas, circuits for handicaped people, electronic mini projects, projects without microcontroller

PushUp Counter

This is a simple circuit for hobbyists. Here i have made a 99 counter with IC's 4026. It counts one when the clock input is supplied with a high to low input, and so on. The clock input is really acting as a switch. So i converted this circuit in to a pushup counter by attaching an IR sensor to the clock input. The IR sensor has a range of 15 cm to 150cm, but only the sufficient clock input is generated by the IR sensor only when some reflective body comes close to it at-least 15cm's. That is the IR sensor acts like a touch-less switch.
Here is the circuit diagram





IR sensor packing
Package size : 29.5×13×21.6 mm




If this IR sensor is kept below your forehead, it will generate clock pulses for the counter when your head comes close to it.

Digital volt meter using PIC 16F676

Buil your own volt meter with PIC 16F676

here is the circuit for making a voltmeter of 3 bit display
Since the pic16F676 have 10bit 8 channel on chip analog to digital converter module, i have used one channel for measuring the input voltage and others are used as digital input/output pins.
Software
This project I use CCS C compiler to programming.The main routine continually read the input voltage on RA3 and convert to 7-segment code while TIMER1 set to timer for interrupt every 5mS for scan all digit about 66Hz(only one digit turn on at every 5mS). In convert digital value to voltage routine we must scale the value with the full scale display in this project I want full scale display at 30V so the input voltage must scaled with 30 and display resolution is 29mV or 30/1023. source code and schematic available here.
Reference: http://www.coolcircuit.com


Tags: PIC 16F676 projects, digital voltmeter, voltmeter using PIC, digital circuit, mini circuits, mini projects, analog to digital converter, microcontroller projects, PIC projects, PIC 16F676 circuits

Sunday, August 19, 2012

EYE INTERFACE TECHNOLOGY



A CURRENT PROJECT BEING DONE UNDER       
INDIAN INSTITUTE OF TECHNOLOGY, MADRAS (IITM)                                                                
                                
TITLE:              EYE INTERFACE TECHNOLOGY
ELECTRO OCULOGRAPHY
                               ---------control of computer with eyes



ABSTRACT:
               Today the use of computers is extended to every field. Many sophisticated devices like touch screen, track ball, digitizers etc made interaction with computer ease from novice to professional. But physically disabled individuals are deterred from using computers due to their inability to control mouse. However, if directional discrimination of an icon can be achieved, quadriplegics can take the function of a mouse without the use of hand. In this paper I come before with a new model of based on Electro-Oculography which uses Electro-oculogram Bio potential amplified signal to control computer .I also discuss its implementation details, including software and hardware design. As my contribution to this paper I introduce a new keyboard design, some modifications in design to overcome the drawbacks in existing model
            In single statement our paper deals with controlling, operating computer with the aid of eyes and this was the project which was done under the precise guidance of Indian institute of technology madras (IITM) in which a live working model costs around 10 lakhs is being built. All the rights of this project strictly belong to IIT, Madras.

In this paper I provide the following details:
 1.  Introduction
 2.  Electro Oculography: Principle
 3.  Design concepts
       4.  Interaction of user with system
 5.  Word processor
 6.  De-merits
 7.  Possible near future improvement
 8.  Performance issues
 9.  Conclusion
10.  Bibliography
 Introduction
              Computer is used in every field now.  Mice and touch screens are a nice improvement over keyboard for some tasks but it can’t be useful for quadriplegics. Although several hardware and software interfaces have been devised for the handicapped computer user, there are no inexpensive systems that deliver the true power and ease of today's computers. It is estimated 150, 00 severely disabled persons able to control only the muscles of their eyes without any problem. This encompasses the construction of the eye-tracking hardware and its fine-tuning in software. 

II. Electro-Oculography
             Through the six extra-ocular muscles by, Absolute eye position Speed Direction of movement, or through the levanter palpebrae (eyelid) and other peri orbital muscles as unilateral or bilateral blinking and blink duration.  Most eye-tracking systems have chiefly addressed the need to measure eye position and/or movement, treating blinks merely as artifact to be discarded. This would be a serious mistake in a practical interface, as will be discussed later. But fortunately, almost all systems can easily be extended to process blink data.
              One eye-tracking method in which blink (and in fact all eye movement) data is particularly simple to collect and analyze, even with very modest equipment, is electro-Oculography. Higher metabolic rate at retina maintains a voltage of +0.40 to +1.0. This cornea-retinal potential is measured by surface electrodes placed on the skin around the eyes.  The actual recorded potentials are smaller, in the range of 15 to 200 micro volts, and are usually amplified before processing event. The potential across two electrodes placed posterior laterally to the outer acanthi is measured relative to a ground lead strapped around the wrist or clipped to the auricle, and the resulting voltage amplified and sent though a custom-built, 8-bit analog to digital converter filtered to remove high-frequency electrical noise. The converter fits into an IBM PC expansion slot, and transmits the digitized data through the PC serial port to a SUN workstation for display. On the positive side, the equipment is cheap, readily available, and can be used with glasses or contact lenses, unlike some reflection methods.

III. Design considerations:
           Eye muscles cannot be operated directly as that of muscles present in the foot and hand. Hands are only the extension of the eye i.e., they select the computer screen as selected by the look. So if we delete the intermediate steps & if we directly control by look it is helpful for both handicapped & non handicapped

 

                                                                                                                                                          
figure : Block Diagram of the Design considerations

The Erica workstation, or eye-gaze response interface computer aid, is an example worthy of study. Erica is based on a standard personal computer specially adapted with imaging hardware and software through near-infrared reflectometry.
Monitor Geometry:
          Take a 19 inch monochrome display with typical pixel configuration of 1024x768 at 72 dpi, for an active display area of 14.22x10.67 inches. When centrally viewed from a distance of 2 feet, this region subtends an angle of 25 degrees vertically, and 33 degrees horizontally.   Maximum EOG or reflect metric resolution is about 1-2 degrees; with menu boxes generously separated by 3 degrees, the 19 inch display still has sufficient room for a 10x4 matrix of directly selectable keys - leaving the entire bottom half of the screen available for a text display area and other controls better. Keyboard implementations should definitely be possible. Fukuda and Yamada is the other selection method. Distinguish between routine eye function and an intentional selection action is necessary. Perhaps the most significant item in this entire project, inexplicably absent from any other eye-controlled system, is the proposed use of a unilateral blink as that selection action. Blinking normally occurs every few seconds, either consciously or unconsciously - but always bilaterally. Blinks are easily detected by EOG as sharp, strong pulses in the vertical channel; since vertical eye movement is always conjugate, a pulse in only one vertical channel is unequivocally a unilateral wink Actual Method: With a 19 inch monitor as described above, a two level keyboard could be laid out in a 10x4 menu box matrix; the bottom half of the screen could display about 25 complete lines of text, and still have additional file, paging, or main menu controls off to the side. The first level of the keyboard would contain all the alphabetic characters, common punctuation, and cursor keys; selecting a special "shift" key would display the second level of the keyboard, with the numbers and less commonly used symbols or editing functions.
IV. Electro-Oculography: Principles and Practice
          EOG is based on electrical measurement of the potential difference between the cornea and the retina. This is about 1 mv under normal circumstances.
 Figure: Placement of Transducer Pickups to Measure Eye Movements 



Figure: Child with the EOG Electrodes
           The Cornea-retinal potential creates an electrical field in the front of the head. This field changes in orientation as the eyeballs rotate. The electrical changes can be detected by electrodes placed near the eyes.
 
        
Figure: The child using EOG
            It is possible to obtain independent measurements from the two eyes. However, the two eyes move in conjunction in the vertical direction. Hence it is sufficient to measure the vertical motion of only one eye together with the horizontal motion of both eyes. This gives rise to the three channel recording system shown in Figure Our eyes need to move in order to keep the image of whatever we are interested in at the central part (called the fovea) of the retina. Thus there are four types of eye movements, called vestibular, opto-kinetic, saccadic, and pursuit. The first two have to do with the largely involuntary head motion.  The saccadic movement is used to "jump" from one object of interest to another.
            The orientation of the eyes is measured by triangulation. The accuracy of the location determination depends on the accuracy with which the eye orientation is determined.  Some of the noise patterns such as the 60 Hz line frequency can be easily removed, using a notch filter. Other noise artifacts are by the turning of an electrical switch on/off in the vicinity of the electrodes contraction of the facial or neck muscles   slippage of the electrode due to sweat and eye blinking. Eye blinking is considered noise in ENG. However, the signals produced by eye blinks are, in fact, quite regular. This makes it easy to recognize and eliminate them.
V. System Design for Location Specification using EOG 
        The work related to the proposed system involves both hardware and software design and development.
The system architecture is shown in Figure
.
                      The hardware part of the system is fairly straightforward. We have completed the design of the amplifier and filter sections and assembled a crude circuit for testing and data collection.  Our overall design philosophy has been to keep the actual add-on hardware (i.e., in addition to the computing hardware) as simple as possible. Thus we have chosen to do most of the filtering and noise removal in software.   The actual hardware fabricated amplifies the voltage picked up by the transducer, removes the electrical line frequency (60 Hz notch filter), and removes high frequency noise (120 Hz low pass stage). Subsequently, the analog signal is converted to digital form and the data samples are sorted in an IBM PC and finally transferred to a UNIX based workstation, where all the software processing will take place.    
Interaction of the System with User:
 The graphics displays in these two modes are


In the synchronizing mode, the system displays a moving cursor and the user is asked to follow the cursor. The cursor follows a fixed path and the user's eye movements are analyzed to verify that the pattern of movement and the cursor motion is the same.  
The second interaction mode is the command mode, where the cursor is moved by the system to track the user's gaze. In our example interface, shown in Figure 3, we show four command "buttons." The cursor is at the center of display (the cross). Imagine that this command system controls a machine, whose speed can be changed. So when the user looks at the start button the cursor follows his or her gaze. Then the command is activated by the user winking twice - i.e., the machine is started. The natural blink & valid blink must be distinguished. Another technique is for transmitting commands. This too should be fairly easy to distinguish from natural eye blinks. When the head is turned away from the screen, the system will be able to detect this because the fixated distance changes from the "norm" recorded during calibration. This will cause the system to disengage and freeze the cursor on the screen. To re-engage the user should perform a gesture such as fixating on the cursor and winking twice
Removal of Noise:
               1. Signal smoothing and filtering to eliminate noise. Calculation of quantitative parameters from the signal channels (two for horizontal movements, one for each eye, and one for vertical movement of the eyes). These parameters are angular positions, angular velocities, and angular accelerations of the eyes. 
               2. Extraction of symbolic tokens from the signal. These tokens indicate the directions of the movement of the gaze (e.g.: North, south).

VI. Current Eye Track System 
             Our objective in this project was to build a 2D point-of-regard controlled spatial locator system and demonstrate its feasibility in a computer graphics environment. The system block diagram is shown in Figure 2 and discussed in Section 5.  We acquire data using an IBM compatible PC and perform software development on a SUN workstation. This decision was based on convenience. Hardware prototyping is inexpensive and quick on the PC bus because of the wide availability of components and printed circuit boards available in the market specifically for this purpose. On the other hand, the window based user interface software (based on Xp windows) is at present better supported on the SUN and other UNIX based workstations. We chose X as our window environment because it is rapidly evolving into an industry standard. In the future, production systems based on our research can easily be wholly resident in the PC, since X products for the PC have already appeared in the market, and we expect such products to dominate window system development within the next few years. The initial work involved hardware equipment setup so that real time signal acquisition could take place. This involved assembling the electrodes, constructing the analog and A/D circuits on a PC form factor board, and interfacing and installing it on the PC bus. The PC was then linked to the SUN via a serial (19.2 Kb) line. Routine software has been developed to enable a program running on the SUN to access the eye movement data captured on the PC and transmitted on the serial line. 
Software Discussion:
          The above discussed software is a 3 x 2 boxed menu driven eye selected interface. This menu has two levels, thus enabling a choice of any letter in the alphabet, as well as some additional punctuation characters. When the program is run, there are several parameters which need to be defined to give the software the ability to make a correct choice (number of calibration repetitions, number of data samples necessary for absolute choice determination, different thresholds, etc.). The above parameters can be set manually, or "automatically", by an auto-calibration mode.
Once the parameters are set, a second calibration mechanism is invoked. The user follows a box which horizontally moves back and forth on the screen, until calibrated. This mechanism is invoked at this experimental stage every time before the software is ready to attempt a menu selection determination.
VII. Possible Near Future Improvements 
             The first and most important change needed by the above described system is a new board. The experimental board contributes to wrong box selection due to erroneous signals resulting from wire wrapping. A new board which is being designed now will have better isolation and more importantly four channels (two per eye) instead of two. This will enable the software performance improvement, as well as some additional features which will be added (e.g. processing of a one eyed wink). This improved board will eventually drive to finer resolution on the screen. The software is being revised to enable better results as well. This will take form in the way of defining optimal parameter choices for the various thresholds and sampling rates, as well as some other minor software improvements. Also needed is a better input device. Attaching electrodes to the skin one by one is cumbersome and annoying for the user. What we need is some device which can be put on by the user himself with ease.

VIII. Conclusion 
             There are many ways to measure eye movement, some far more accurate than EOG, but these are expensive. Furthermore, the eye tracking method is just a means, one in which pinpoint accuracy is not really necessary; the provided service and ease of use of the eye-controlled interface is the true goal. We aim to improve the existing eye-tracking system and will attempt to resolve the current faults and weaknesses, and implement the eye-tracking device in the most user friendly and efficient interface we can devise.

Bibliography:
Young and Sheena, "Survey of eye movements recording methods"
Behavior Research Methods and Instrumentation, Vol. 7 (5), 1975   Hutchinson
"Human-Computer Interaction Using Eye-Gaze Input", IEEE
Transactions on Systems, Man, and Cybernetics, Vol. 19, No. 6, 1989
Bahill, A. T., Bioengineering: Biomedical, Medical and Clinical Engineering, Prentice-
Hall, Inc., Englewood Cliffs, NJ, 1981. 


Saturday, August 18, 2012

Railway Track Snap Notification



A Prototypic Implementation of  Wireless Based Railway Track Snap Notification with Alarm Systems 
SYNOPSIS:
The Safety Risk Model (SRM) is RF Based representation of risk on Rail track controlled infrastructure (RCI). It provides a structured representation of the causes and consequences of potential accidents arising from railway operations and maintenance the over bridge for river.
PROBLEM STATEMENT:
In railway bridges, any time the bridge its striking due to weather condition, floods, earthquake, cyclone, etc. Now days system have some limitations, if the bridge or track damaged, that information goes to railway authority people, they notifies and informs to the corresponding trains it will takes more time informing those information. So to avoid delays, our proposed system will immediately notifies and informs the current train comes on the track through wireless medium.

Car Battery Charger



Here is a simple circuit for charging car battery( 12v). The circuit contains:
  • a 230 - 12 step down transformer, 3 amp
  • bridge rectifier circuit 
In this circuit the 230V ac supply is converted to 12V ac supply by the step down transformer and then this 12V ac is rectified to 12V dc by the bridge rectifier. There is a capacitor at the output of the bridge rectifier, it is used for filtering.
This circuit can also be used as a 12V dc power supply.





Tags: battery charging circuit, 12v battery charging circuit, car battery charger, car battery charging circuit, rectifier circuit

Basketball Score Counter


This is a circuit for making a counter that can be used to count the score in basketball games.
There a 3 seven segment displays. 

IR sensor

Package size : 29.5×13×21.6 mm




If this IR sensor is kept below your forehead, it will generate clock pulses for the counter when ball passes across it


Wireless Spy Sound Recorder

Description


In this project i had designed a spy device for capturing and transmitting sound to a distant place. In the receiver there is also a circuit for recording.

Automotive Telematics



A Prototypic Design Approach for Automotive Telematics On-board Unit Platform (ATOP) Using ARM Powered NFC (Near Field Communication) Technology


SYNOPSIS:
                In today’s fastest world the use of vehicle is unavoidable as well as the accident occurring due it is also a biggest issue.  So we have designed the system in a move to save lives on the road by measuring the pressure of the vehicle. Current estimates suggest annually there are around 43,000 deaths across Europe’s road networks. Experts believe this could be reduced significantly if the load of the vehicle is maintained as well as the traffic is also maintained by allowing the heavy vehicles only in the specific time.
PROBLEM STATEMENT:
         Measuring the load and perimeters are crucial
          Detection of the vehicle is difficult
         Miscellaneous of  vehicle in the city for long durations

PROPOSED SYSTEM:
In this proposed system we have designed the system with three applications. First application is to calculate the strain of the vehicle. By using strain sensor, pressure of the vehicle is monitored. When the strain exceeds the set up value the information is suddenly passed to the RTO office through wireless technology. By using this application over loading of the vehicle can be avoided which may lead to an accident. So by using this system even if the owner tried to overload his vehicle he can’t do it. By using this system driver can drive his vehicle safely and accident freely.
In the second application traffic jam can be reduced by maintaining the specific time for heavy vehicle. Heavy vehicles should enter the city only at the specific time. If they entered at some other time information is transferred to the control room.
The third application is used to maintain the traffic signal properly. If any vehicle crosses the road when the signal is red .Then the vehicles id is passed to the nearest control room. Intruder sensor is used to detect whether the vehicle crosses the road in the proper way or not.

BLOCK DIAGRAM:
Vehicle section:
















Control Room Section:


 











Signal Section:




















REQUIREMENTS:
Hardware Requirements:
Ø  Microcontroller
Ø  RF module
Ø  Decoder/encoder
Ø  Pressure sensor
Software Requirements:
Ø  Keil IDE
Ø  Flash magic
Ø  ORCAD
Ø  Embedded C

APPLICATIONS:
         Highly Reliable.
         Traffic signal will be controlled
         Automatic fine can be charged using wireless technology
         Much more efficient than the existing system.
 

Thursday, August 16, 2012

Smart Car




SYNOPSIS:

In modern world, many new techniques such as biometric recognition technique, image processing technique, communication technique and so on, have been integrated into car security systems. At the same time, the amount of accident of cars still remains high, specially, lost. Traditional car security systems rely on many sensors and cost a lot. When one car is really lost, no more feedback could be valid to help people to find it back.

PROBLEM STATEMENT:
       No information to the Owner if Car get Lost
       Traditional car security systems rely on many sensors and cost a lot
        Physical Key.
       Alarm System

PROPOSED SYSTEM:

In proposed system we introduced a low-cost extendable framework for embedded smart car security system is proposed, which consists of a face detection subsystem(FDS), a GPS (Global Positioning System) module, a GSM (Global System for Mobile Communications) module and a control platform. The face detection technique to be applied in car security system because this kind of technique is effective and fast, and one alarm signal could be given to make an alarm or “call” the police and the host soundlessly with the help of other modules in the system prototype. Experimental results illuminate the validity of this car security system, and it is also much cheaper and ‘smarter’ than traditional ones.
FDS (face detection subsystem) is used to detect the face of the driver and compare it with the predefined face, for example, in the night when the car’s owner is sleeping and someone theft the car then FDS obtains images by one tiny web camera which can be hidden easily in somewhere in one car. FDS compares the obtained image with the predefined images if the image doesn’t match then the information is send to the owner through MMS. So now owner can obtain the image of the theft in his mobile as well as he can trace the location through GPS.  The location of the car as well as its speed can be displayed to the owner through SMS. So by using this system owner can identify the theft image as well as the location of the car.
Block Diagram:

Vehicle Section:

 
                                                                    






 

HARDWARE REQUIREMENTS:
      Microcontroller
      Power supply
      Keypad section
      GSM module
      Web Camera
      Ignition unit | Driver unit

SOFTWARE REQUIREMENTS:
      Keil C cross compiler IDE
      Flash magic programmer tool
      Orcad hardware design tool
      Visual basic 6.0
      Matlab7.5
      Languages:
     Embedded C
     Visual Basic

APPLICATIONS:
      Security applications
      Image processing applications
      Banking applications